Werks Clutch

If it smells like Nitro, it belongs in here!
Post Reply
macka
Posts: 101
Joined: Sat Jan 15, 2011 8:20 am
Location: Palmerston North

Tue Jan 09, 2018 9:32 am

What clutch bell can you use on the Werks pro 4 clutch system?
I run losi vehicles im looking at going werks and ditching the losi clutch.

Does the losi clutch bell fit?
Losi 8ight-T 3.0 Werks b5 pro
Losi 8ight 3.0 Argus R8
Losi 8ight-E 2.0 Tekin
Losi Ten-Scte Tekin

User avatar
ASA
Posts: 1003
Joined: Sat Jun 09, 2012 3:46 pm
Location: Te Aroha

Tue Jan 09, 2018 1:03 pm

You will have to run the 2 piece engine mount on the losi so you can run it with the engine in the forward position and then pretty much most bell types other than the losi type....they are specific to the losi cars
WERKS RACING NZ - OUTLAW RC
HB Racing D817 Werks B3 Pro2
HB Racing D817T Werks B3 Pro2

macka
Posts: 101
Joined: Sat Jan 15, 2011 8:20 am
Location: Palmerston North

Tue Jan 09, 2018 2:18 pm

Cheers for that.

Im already running the losi quick change engine mounts on both buggy and truggy so that's good.

Any suppliers out there sell 12t clutch bells that aren't losi type?
Losi 8ight-T 3.0 Werks b5 pro
Losi 8ight 3.0 Argus R8
Losi 8ight-E 2.0 Tekin
Losi Ten-Scte Tekin

User avatar
ASA
Posts: 1003
Joined: Sat Jun 09, 2012 3:46 pm
Location: Te Aroha

Tue Jan 09, 2018 4:40 pm

All good bud......that will be the next problems is finding a 12t bell in NZ that isn't losi type as most things run 13t or bigger :?
WERKS RACING NZ - OUTLAW RC
HB Racing D817 Werks B3 Pro2
HB Racing D817T Werks B3 Pro2

macka
Posts: 101
Joined: Sat Jan 15, 2011 8:20 am
Location: Palmerston North

Fri Jan 26, 2018 9:06 am

Next question about this clutch setup on a losi is whether you use the losi clutch collet and nut or the werks collet and nut? Im trying a 2nd hand unit that wasn't on a losi before.
Losi 8ight-T 3.0 Werks b5 pro
Losi 8ight 3.0 Argus R8
Losi 8ight-E 2.0 Tekin
Losi Ten-Scte Tekin

User avatar
ASA
Posts: 1003
Joined: Sat Jun 09, 2012 3:46 pm
Location: Te Aroha

Fri Jan 26, 2018 11:48 am

You should always use the collet that comes with the flywheel as different makes have different tapers etc,......the nut not as crucial but if there is a signicant difference in length and it requires a heap of thrust washers to get bell to flywheel clearance the try another nut (y)
WERKS RACING NZ - OUTLAW RC
HB Racing D817 Werks B3 Pro2
HB Racing D817T Werks B3 Pro2

Post Reply
  • Information
  • Who is online

    Users browsing this forum: Bing [Bot] and 8 guests